TLK1201A 具有半速率选项的千兆以太网收发器
The TLK1201A/TLK1201AI gigabit ethernet transceiver provides for ultrahigh-speed, full-duplex, point-to-point data transmissions. This device is based on the timing requirements of the 10-bit interface specification by the IEEE 802.3 gigabit ethernet specification and is also compliant with the ANSI X3.230-1994 (FC-PH) fibre channel standard. The device supports data rates from 0.6 Gbps to 1.3 Gbps.
The primary application of the transceiver is to provide building blocks for point-to-point baseband data transmission over controlled impedance media of 50 
. The transmission media can be printed-circuit board traces, copper cables, or fiber-optical media. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the environment
|
TLK1201A |
| Gbps per Serial Channel(Min) |
0.6 |
| Gbps per Serial Channel(Max) |
1.3 |
| ICC(Max)(mA) |
90 |
| IIH(Max)(uA) |
40 |
| IIL(Max)(uA) |
-40 |
| Power Consumption(Nom)(mW) |
250 |
| Number of Serial Channels |
1 |
| Parallel Bus Width |
10 |
| Parallel I/F |
LVTTL |
| Serial I/F |
LVPECL |
| Operating Temperature Range(C) |
0 to 70 |
| Pin/Package |
64HVQFP |
| VCC(Min)(V) |
2.3 |
| VCC(Max)(V) |
2.7 |
| VCC(Nom)(V) |
2.5 |
| VIH(Min)(V) |
1.7 |
| VIH(Max)(V) |
3.6 |
| VIL(Max)(V) |
0.8 |
TLK1201A 特性
- 0.6-Gbps to 1.3-Gbps Serializer/Deserializer
- Low Power Consumption <200 mW at 1.25 Gbps
- LVPECL Compatible Differential I/O on High Speed Interface
- Single Monolithic PLL Design
- Support For 10-Bit Interface or Reduced Interface 5-Bit DDR(Double Data Rate) Clocking
- Receiver Differential Input Thresholds 200 mV Minimum
- IEEE 802.3 Gigabit Ethernet Compliant
- ANSI X3.230-1994 (FC-PH) Fibre Channel Compliant
- Advanced 0.25-um CMOS Technology
- No External Filter Capacitors Required
- Comprehensive Suite of Built-In Testability
- IEEE 1149.1 JTAG Support
- 2.5-V Supply Voltage for Lowest Power Operation
- 3.3-V Tolerant on LVTTL Inputs
- Hot Plug Protection
- 64-Pin VQFP With Thermally Enhanced Package (PowerPADTM)
- CPRI Data Rate Compatible (614 Mbps, 1.22 Gbps)
- Industrial Temperature Range Supported: -40°C to 85°
TLK1201A 芯片订购指南
| 器件 |
状态 |
温度 |
价格 |
封装 | 引脚 |
封装数量 | 封装载体 |
丝印标记 |
| TLK1201ARCP |
ACTIVE |
0 to 70 |
4.70 | 1ku |
HVQFP (RCP) | 64 |
160 | JEDEC TRAY (10+1) |
|
| TLK1201ARCPG4 |
ACTIVE |
0 to 70 |
4.70 | 1ku |
HVQFP (RCP) | 64 |
160 | JEDEC TRAY (10+1) |
|
| TLK1201ARCPR |
ACTIVE |
0 to 70 |
3.90 | 1ku |
HVQFP (RCP) | 64 |
1000 | LARGE T&R |
|
| TLK1201ARCPRG4 |
ACTIVE |
0 to 70 |
3.90 | 1ku |
HVQFP (RCP) | 64 |
1000 | LARGE T&R |
|
TLK1201A 质量与无铅数据
| 器件 |
环保计划* |
铅/焊球涂层 |
MSL 等级/回流焊峰 |
环保信息与无铅 (Pb-free) |
DPPM / MTBF / FIT 率 |
| TLK1201ARCP |
Green (RoHS & no Sb/Br) |
CU NIPDAU |
Level-3-260C-168 HR |
TLK1201ARCP |
TLK1201ARCP |
| TLK1201ARCPG4 |
Green (RoHS & no Sb/Br) |
CU NIPDAU |
Level-3-260C-168 HR |
TLK1201ARCPG4 |
TLK1201ARCPG4 |
| TLK1201ARCPR |
Green (RoHS & no Sb/Br) |
CU NIPDAU |
Level-3-260C-168 HR |
TLK1201ARCPR |
TLK1201ARCPR |
| TLK1201ARCPRG4 |
Green (RoHS & no Sb/Br) |
CU NIPDAU |
Level-3-260C-168 HR |
TLK1201ARCPRG4 |
TLK1201ARCPRG4 |
TLK1201A 应用技术支持与电子电路设计开发资源下载
- TLK1201A 数据资料 dataSheet 下载.PDF
- TI 德州仪器串行器和解串器选型与价格 . xls
- 所选封装材料的热学和电学性质 (PDF 645 KB)
- 使用数字隔离器设计隔离式 I2C 总线接口 (zhct119.PDF, 339 KB)
- 高性能SERDES及其在CPRI 接口的应用分析 (zhca076.HTM, 8 KB)
- 1Q 2011 Issue Analog Applications Journal (slyt399.PDF, 964 KB)
- 接口选择指南 (Rev. D) (PDF 2994 KB)
- Signaling Rate vs. Distance for Differential Buffers (PDF 420 KB)
- Q1 2009 Issue Analog Applications Journal (slyt319.PDF, 1.39 MB)
- Isolated RS-485 Reference Design (PDF 80 KB)
- 无铅组件涂层的保存期评估 (PDF 1305 KB)
- Analog Signal Chain Guide (8.62 MB)
- Industrial Interface IC Solutions (101 KB)
TLK1201A 工具和软件