首页 > TI 德州仪器 > 逻辑 > 触发器/锁存器/寄存器

SN54LVTH16373 具有三态输出的 3.3V ABT 16 位透明 D 类锁存器

The 'LVTH16373 devices are 16-bit transparent D-type latches with 3-state outputs designed for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. These devices are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers.

These devices can be used as two 8-bit latches or one 16-bit latch. When the latch-enable (LE) input is high, the Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs are latched at the levels set up at the D inputs.

A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus lines without interface or pullup components.

OE does not affect internal operations of the latch. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

When VCC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict

SN54LVTH16373
Voltage Nodes(V) 3.3, 2.7
Rating Military
SN54LVTH16373 特性
SN54LVTH16373 芯片订购指南
器件 状态 温度 价格(美元) 封装 | 引脚 封装数量 | 封装载体 丝印标记
SNJ54LVTH16373WD ACTIVE 5962-9074601MSA 13.44 | 1ku CFP (W) | 48 1 | TUBE  
SN54LVTH16373 质量与无铅数据
器件 环保计划* 铅/焊球涂层 MSL 等级/回流焊峰 环保信息与无铅 (Pb-free) DPPM / MTBF / FIT 率
SNJ54LVTH16373WD TBD Call TI N/A for Pkg Type SNJ54LVTH16373WD SNJ54LVTH16373WD
SN54LVTH16373 应用技术支持与电子电路设计开发资源下载
  1. SN54LVTH16373 数据资料 dataSheet 下载.PDF
  2. TI 德州仪器触发器/锁存器/寄存器产品选型与价格 . xls
  3. Shelf-Life Evaluation of Lead-Free Component Finishes (PDF 1305 KB)
  4. Understanding and Interpreting Standard-Logic Data Sheets (PDF 857 KB)
  5. TI IBIS File Creation, Validation, and Distribution Processes (PDF 380 KB)
  6. Implications of Slow or Floating CMOS Inputs (PDF 101 KB)
  7. CMOS Power Consumption and CPD Calculation (PDF 89 KB)
  8. Designing With Logic (PDF 186 KB)
  9. Live Insertion (PDF 150 KB)
  10. Input and Output Characteristics of Digital Integrated Circuits (PDF 1708 KB)
  11. Using High Speed CMOS and Advanced CMOS in Systems With Multiple Vcc (PDF 43 KB)
  12. HiRel Unitrode Power Management Brochure (PDF 206 KB)
  13. LOGIC Pocket Data Book (PDF 6001 KB)
  14. HiRel Unitrode Power Management Brochure (PDF 206 KB)
  15. Logic Cross-Reference (PDF 2938 KB)